• Archives

  • Categories

  • Pages

How do I know if it’s a leak or evaporation loss?| Decorative Ponds & Water Gardens Q & A

Q: How do I know if it’s a leak or evaporation loss?

Q: How do I know if it’s a leak or evaporation loss?

Dena – Albrightsville, PA

A: A little water loss in your water garden is normal – but when it disappears by the inches, you’ve got a mystery to solve. These step-by-step sleuthing tips, below, can help you deduce whether it’s summertime evaporation or a liner leak.

Step 1 – Look for Evaporation Clues

During the heat of the summertime, you can expect some all-natural water loss. Thanks to evaporation, up to an inch (give or take) of water will naturally disappear from the pond, and if you have a long stream bed with a lot of surface area or a large pond with few floating plants, even more water could transform from liquid to vapor. If you suspect evaporation, fill the pond back up and keep an eye on the water level.

Step 2 – Check for Dampness Around the Pond

If more than an inch of water is disappearing every day, you could be dealing with a leak. Walk around the pond and waterfall or stream, and carefully inspect the soil for signs of unexplained moisture. If you find some, take a closer look at that spot’s liner and construction. Leaking water has to go somewhere, and a patch of wet ground is clear indicator of a problem.

Step 3 – Finding Liner Rips

If you suspect a rip or hole in your liner, keep a close eye on the pond’s water level until it stops falling. When it does, that’s when you should look for the leak. Because the water level will stabilize once it lowers past the hole, you should be able to find the problem at or below the water level and fix it.

To repair the leak, you have two options: repair the hole with a patch found in the EPDM Pond Liner Patch Kit, or close it up with some underwater sealer, like Gold Label Pond and Aquarium Sealer. The patch kit comes with everything you need to fix minor tears in your pond liner, including an EPDM patch, solvent wipe, scrub sponge, seam roller and pair of disposable gloves. The underwater sealer, which works on wet or dry surfaces, instantly repairs leaks in rubber and vinyl liners.

Step 4 – Shore Up Your Stream

If you found moisture outside of your stream or waterfall, turn off your pump and inspect the rocks and liner around the wet spot. Is there a hole in the liner? Repair the leak with your liner patch kit. Is water pooling under rocks or splashing outside the stream? Redirect it back down to the pond with Black Waterfall Foam. Once you apply it, it’ll look like shadows between the rocks.

Step 5 – Inspect Your Fittings

Finally, if you’ve ruled out evaporation and there are no damp areas around the circumference of your pond to be found, the culprit could be your pressurized filter, tubing or connections. Inspect the plumbing on the pump or waterfall where pipe splits or loose fittings could be leaking, and repair it as necessary.

Good luck finding the cause of your pond’s water loss!

Pond Talk: How much water evaporates from your pond per day in the summertime?

Patch Leak Even Underwater - Gold Label Pond & Aquarium Sealer

I added too much pond dye. What do I do? | Ponds & Lakes Q&A

Q: I added too much pond dye. What do I do?

Q: I added too much pond dye. What do I do?

Roy – Bend, OR

A: Pond dye is a good thing for many reasons, like algae control, aesthetics and camouflage from predators. Plus, it’s totally safe for animals, fish and humans who like to go for a dip in the water. But too much pond dye can create a monochromatic mess that looks totally unnatural in a landscape.

So what can you do? Not much, unfortunately. The only practical solution is to wait it out while long periods of sunshine fade the color or heavy rains dilute the dye. It will eventually lose its black or blue hue, but it will take a bit.

To prevent this from happening again, calculate your pond’s surface area and depth before you add color to your pond or lake so that you use the right amount of dye. Two Pond Dye Packets or one liquid quart of Pond Dye Concentrate treats up to one surface acre with an average depth of four to six feet deep.

Here’s how to figure out those important numbers:

Surface Area: First, figure out your pond’s square footage. If it’s rectangular or square, determine its size by simply measuring its length and width and multiplying them (250 feet x 250 feet = 62,500 square feet). If your pond is irregularly shaped, break it up into several segments, measure or pace off each one’s length and width, calculate the square footage and add them together. [(100 feet x 300 feet) + (40 feet x 50 feet) = 30,000 + 2,000 = 32,000 square feet.]

To determine your pond’s surface area, divide its total square footage by 43,560. So in the above example, 62,500 square feet / 43,560 = ~1½ acres; and 32,000 square feet / 43,560 = ~3/4 acre.

Pond Depth: To measure its depth, gather some tools, including a tape measure, some chain or string, a weight, something to write with, and a boat or canoe. Mark a chain or knot a string in 1-foot intervals using your tape measure and attach the weight to one end. Climb aboard your boat, travel to various areas in your pond and drop the weight in the water, noting where you feel it hit bottom. Take an average of those measurements to get your depth.

Once you have your numbers, use the appropriate amount of dye. Unsure of your pond’s size? No worries! Add 1 packet and wait 24 hours. If it looks like you need more, add another packet. Simple as that!

Pond Talk: Have you ever had a pond dye problem in your pond or lake? If so, what happened – and how did you correct it?

Shade & Protect Your Pond - Pond Logic® Pond Dye Packets

Follow

Get every new post delivered to your Inbox.

Join 142 other followers